Troubleshooting - Your Vpn doctor for Virtual private Network Troubleshooting Vpn Guide
Good afternoon. Now, I found out about Troubleshooting - Your Vpn doctor for Virtual private Network Troubleshooting Vpn Guide. Which is very helpful in my experience so you. Your Vpn doctor for Virtual private Network Troubleshooting Vpn GuideHere are some troubleshooting guides for single topics.
What I said. It is not in conclusion that the real about Troubleshooting. You check this out article for information on an individual want to know is Troubleshooting.Troubleshooting
(1) Your Virtual Network Connection
(2) Vpn Troubleshooting Error Messages
(3) Vpn Modems Troubleshooting Guide
(4) Vpn Isp Troubleshooting Guide.
(1) Your Virtual secret Network Connection
Having problem connecting to the Internet at home try these steps before calling for help.
1. Do you have an Ip address? Try ipconfig /all. If you do not have an Ip address reboot your Pc. If that doesn't work power cycle your Cable/Dsl modem and routers and reboot your Pc again after the network devices are up and stable. Be sure all of your network cables are plugged in tight.
2. After your Pc reboots check that your network adapter is active and packets are flowing. Accomplish the ipconfig /all check again.
3. Check your connectivity by pinging several Internet sites. If that does not work, ping the loopback address 127.0.0.1. If that fails, your adapter may not be working or it is not properly configured.
To check your Ip address. From command prompt enter ipconfig /all (as shown in the picture) you should see an Ip Address and several Dns Server addresses. The domain name theory (Dns) is the way that Internet domain names are placed and translated into Ip addresses and is required for browsing the Internet.
Ping 127.0.0.1 - loopback Test (as shown in the picture). The loopback test is used to check if the Ip stack is responding. If it times out or you get an error the question may occur if any one or more of the following conditions is true:
*The Tcp drivers are corrupted
*The network adapter is not working
*Another aid is interfering with Ip
Check your network adapter, click the Start menu, Settings, operate Panel, and pick Network Connections. Double click on the Local Area association or the Wireless Adapter whichever one you are using. Be sure its Connected. If you have multiple network cards disable the one you are not using.
There should be Packets displayed in both the Sent and Received counters. If the Received counter is 0 check that the adapter has an Ip address. pick Properties.
Click the check boxes for Show icon and post me below. A twin Pc icon will appear on the lower right measure of the taskbar in the tray area and will flash while sending and receiving packets. You can place your mouse over the icon to get the status and click on it to get more details.
Tracert displays the association path to the target location and the whole of hops. Each hop is the trip from one router to another. Tracert is a handy tool both for understanding where problems are in the network and for determining latency in the middle of hops.
Ping is used to conclude either a host exists and is active on the network and can conclude the round trip time to the device. You can enter a host name or an Ip address if you know it. If the request times out then the host is not reachable because it's offline or there is a question with the connection. Try several sites, if none work then ping the loopback address 127.0.0.1 Also, if your Dns is not working or properly configured you can only ping the host with an Ip address and you will not be able to browse the Internet.
If you are having intermittent problems, Accomplish a ping -t for 5 to 6 minutes then hit Ctrl C to see the results of the test to conclude if you are dropping network packets (lost packets). If you are, this normally indicates an Isp question or Cable/Dsl modem problem. See Vpn Isp Troubleshooting Guide
(2) Vpn Troubleshooting Error Messages
Q1 Error Message: Remote Host not responding: or Unable to conclude the Ip address of the Remote Server
Cause: This indicates that the Contivity Vpn Switch never responded to the association attempt. The question could either be with the Contivity switch itself, (switch may be down) or your machine may be having a question resolving the Ip address.
Action: Try pinging your destination name (Example: Vpn.something.com). If you received a message that says "Request Timed Out" from the ping command, call your Isp to make sure that their Dns is functioning correctly.
Q2 Error Message: Maximum whole of sessions reached
Cause: This indicates that the maximum whole of users for the catalogue you are using are currently logged on.
Action: If you are the only user with Vpn to your account, it is inherent to get this error if you restarted a association immediately after losing the dial-up association to your Isp. This is because the Contivity Vpn Switch takes up to one hour to conclude that your association has been dropped and log you off from your account.
Q3 Error Message: Login failed, Please consult the switch log for added information
Cause: The User Name or the Password is incorrect for the user name entered.
Action: Verify that the User Name you entered is definite and retype the Password before trying the association again.
Q4 Error Message: The bodily association has been lost
Cause: Your association to your Isp was disconnected.
Action: Re-establish your association to your Isp before you re-establish the Contivity association to the remote network.
Q5 Error Message: The accumulate Contivity association has been lost
This message can effect due to a whole of separate reasons, and there are several recommended actions you can take to try and re-connect.
Cause(s):
If you receive this error before the client connects then something is blocking a principal port (such as Esp port 50). This can effect if your firewall is not configured properly and is restricting the principal port(s).
If you receive this error during a association and you suddenly get the error it may mean one of the following:
1. Something concluded the connection;
2. The Vpn Contivity switch where you were trying to join together to view your client was down or timed out;
3. Your local Isp did something that interrupted your network association long sufficient for the Vpn Contivity switch to identify your client was not responding;
4. The Vpn Contivity switch that you are connected to has either logged your association off or the Switch is no longer responding, or a gismo that does not keep Ipsec Nat Traversal is causing the association failure.
Action(s):
1. Try re-establishing the Contivity association by clicking the join together button. If this works, the association was probably lost due to the Idle Timeout configured on the Contivity Vpn Switch. If no data is transferred through the Contivity association for a long period of time, 15 minutes or more, the Contivity Vpn Switch automatically disconnects the connection;
2. If you were unable to successfully re-establish the Contivity Connection, the dial-up association may be preventing data from traveling in the middle of the Contivity Vpn Client and the Contivity Vpn Switch. Hang up the dial-up association and reconnect before you try to re-establish a association to the Contivity Vpn Switch;
3. If you are still unable to join together to the Contivity Vpn Switch, open a Command Prompt and try pinging the Contivity Vpn Switch using the host name or address that you specified in the Destination field.
(a) If you receive a "Destination Unreachable error" there is a routing question at the Isp.
(b) If you receive a "Request Timed Out" error message, the Contivity Vpn Switch is probably not available, and you should touch your Network Administrator.
4. If you keep getting this message and are unable to connect, then it may indicate that the Contivity Vpn Switch is unable to reveal with the client because it is behind some kind of Nat (Network Address Translation) device. Nat (Network Address Translation) Traversal allows a whole of devices on a secret network to way the Internet simultaneously without each requiring its own external Ip address. Most hotels and airports that supply Internet connectivity use Nat to join together to the Internet.
Q6 Error Message: Cannot Alter Routing Table
Cause: Message means the you the user, an application on your machine, or your Isp attempted to change the routing table via an Icmp redirect endeavor and it was not successful. The client detects the endeavor to make the change, determines it's a protection breach and shuts down the client's connection. Any time you make a Vpn connection, you cannot change the routing table, because the Vpn Client views this as a protection risk and you will get disconnected.
Some applications need an Icmp redirection in order to work such as a game or other third party software.
Action: If you receive this error and cant join together due to an Icmp redirect attempt, shut down any other applications you are using which may be causing the Icmp redirect attempt. If it is the Isp that is doing it, you will need to block the Icmp redirect request. You can identify that Icmp redirect has occurred, by finding a message saying there has been an Ip address routing table change.
Q7 Error Message: Receiving Banner Text Information
Cause: Message means you are experiencing a Banner Sock issue, and will see a window displaying the "Receiving Banner Text" message and then gets disconnected.
Actions:
1. Disable the firewall completely to test. This is a port 500 issue and often means that the you have a personal Firewall that is blocking port 500 or you have a router that does not keep Ipsec pass-through, and the you are connecting to a Vpn switch that does not have Nat Traversal enabled.
2. If using wireless, temporarily take off Wireless from the photograph and focus on the Ethernet card. Check the Ethernet card speed and duplex parameters and then make sure that the hub, switch, or router that is on the other end has the same parameters. If not, the Vpn association will drop as the link goes up and down, or due to a large whole of errors on the port from a duplex and or speed mismatch.
3. Firewall that blocks the connection, such that theory will crash. (This will rarely happen) Nsdf (Norton Symantec Desktop Firewall) and Nspf (Norton Symantec Personal Firewall) can do this though, if you do not trust the Ip address of the Vpn connection.
If you do not trust the Vpn address of the Vpn client, the firewall will cause you to crash. In your Internet browser click on "Tools > Internet Options > protection > Trusted Sites > Sites" and add the destination Vpn address(es) to your trusted sites.
Q8 Error Message: You already have the maximum whole of adapters installed
Cause: You may have installed to many virtual adapters in your Ip Stack
Actions:
1. take off any unnecessary adapters;
2. Create multiple boot scenarios disabling the adapters that are not required for that function;
3. You may also get Banner Sock errors on Win 95 & 98 units with this condition;
4. For more information, see this Microsoft article: Kb217744: Unable to Bind Protocols to More Than 5 Network Adapters (copy and paste into the hunt tool bar > enter).
Q9 Upgrade Errors: The following are some errors that may occur when trying to upgrade / install the Nortel Vpn Client 4.65
Error (1): Failed to get Registry key value for Nt_Ipsecshm
Cause: This is caused because an foremost registry key that cannot be found in the theory registry.
Actions:
1. Uninstall and Reinstall the Vpn Software
Error (2): Login Failure due to: Driver Failure
Cause: This is commonly caused by either not having Admin rights to the Pc or by trying to install/use a Nortel Vpn client that predates the operating system.
Actions:
1. Ensure that you have admin rights to the Pc.
2. Update/Install the most current version of the Nortel Vpn client.
Error (3): Create socket failed with 10048.
Cause: This question commonly will occur whenever you have another Vpn client software installed on the system. The most noted conflicting clients are: Aol, Cisco Vpn Client(s), Ssh Sentinel and Pgp.
Actions:
1. Removing these clients will in most cases, conclude the issue.
(3) Vpn Modems Troubleshooting Guide
Q1 Are Cable Modems supported for Vpn Access?
Yes, you can use cable modems for Vpn access. However you must be aware of the following conditions and be able to work within them:
*Some cable modems need that you log into an Nt network to get authenticated.
*Some cable modems use a client similar to the Extranet Client for Vpn and both will not run at the same time.
*Some cable modem Contracts/Acceptable Use Policies specify that you cannot use them for enterprise purposes or they want to charge you another fee to use them for enterprise purposes. Make sure you read your contract thoroughly.
*Your Cable modem supplier is your Isp. Please see the Vpn-connection-guide.html">Isp Troubleshooting Guide for more information.
Q2 Why does my modem seem to Accomplish erratically?
Always make sure that you do not let the operating theory pick a generic modem. If required, go to the acceptable web site for the vendor of the modem and get the updated Inf file so that the allowable parameters are configured for the modem.
Q3 Why do I always seem to get a slower association speed than others with the same modem?
1. always check the modem configuration to verify that its maximum speed has been selected.
2. It is coarse when auto-installing modems that the top speed is not superior automatically.
3. Do not check the box that says run at maximum speed only.
Q4 I plugged my modem into the phone line at the hotel or customers office and now it does not work.
Always make sure that the phone line you are plugging into when visiting somewhere is an analog line not a digital one. Plugging into a digital line can enduringly damage your modem, requiring a change unit. To avoid these situations please touch the local site phone keep personnel.
Q5 Why cant I get a 56Kb V.90 association from some locations that I go to?
Here are some of the reasons why you might not get a 56K connection:
1. You are placed more than 3 ½ miles from your telephone companys central office (Co).
2. A Slick or Subscriber Loop theory is used in your area.
3. You are calling from a digital Pbx system, which creates a Digital to Analog conversion and then an Analog to Digital conversion.
4. Your line contains digital pads or Robbed Bit Signaling (Rbs), which can degrade your association speeds.
5. Your wiring may be of poor quality.
6. Your modem's firmware may not be up-to-date. Check that your modem has the most recent V.90 code installed with all the patches from the vendor's web site.
Q6 Why cant I get higher speed on my 56K v.90 modem into some Nag?
Here are some inherent reasons:
1. A 56k v.90 modem is asymmetric by develop where download speed can be as much as 56k but upload speed will be up to 33.6bps. For 56k to work, there must be only one analog-to-digital (A/D) conversion in your local phone loop. Thus when modems at both ends are analogue, 56k speeds will never be achieved as most Pstn exchanges run digital routing in the middle of the exchanges.
2. Some Nag sites use analog phone lines with Cisco and acceptable 56k modems, and most Pc's dial-ups use a similar modem. in the middle of the two modems, it limits the download speed to about 33.6kbps maximum.
3. Also, many users might touch lower association speeds due to other reasons, such as more poor line quality. These factors will also conduce to the capability and speed of the line.
(4) Vpn Isp Troubleshooting Guide
Q1 If you are getting the message "Unable to conclude the Ip address of the Remote Server. Verify the Host Name in the destination field is correct." when trying to join together with the Extranet Client.
Try pinging your destination name (Example: Vpn.something.com) and if it fails call your Isp to make sure that their Dns is functioning correctly.
Q2 Why do I get No Domain ready when dialing my Isp?
On your Internet aid Providers (Isp) dial connection. Right click the mouse and pick the properties button. Click on the Server Type tab and make sure that the Log On To Network box is unchecked.
Q3 Why do I seem to be running gently through my Vpn connection?
Try turning off the Software Compression choice on your Internet aid Providers (Isp) dial association as the Vpn client has it's own compression. Right click the mouse and pick the properties button. Click on the Server Type tab and uncheck the
Q4 I keep getting busy signals when trying to join together to my Isp, what should I do?
Contact your Isp giving the numbers you are trying to join together to. Many times you will find that can give you an alternate whole not published yet that will work just fine. If not you may need to find another Isp that provides better service.
Q5 When configuring the dial icon for my Isp what should I put in the Dns/Wins settings?
Your Isp should supply you with the Dns/Wins settings of your dial connection. Most only give you Dns, in this case just leave the Wins settings blank.
Q6 Why when I load the Extranet Client on my Pc and Winpoet is installed on my machine it crashes or does not work properly?
There are issues running Winpoet software on the Pc with the Nortel Extranet (Vpn) Client.
To heal your system, boot in safe mode and uninstall the Winpoet Software.
A simple explication is to install the Linksys Befsr41 hardware router. It has a firmware Pppoe connector, which eliminates Winpoet from the Pc and provides the added advantage a Nat firewall with the capability to hook up to three other Pcs.
A second choice is to find a Pppoe Client that does not interfere with Vpn Clients.
Please See Your Vpn physician for photograph Guide and added Details.
Need a Qiuck Fix, Tool, Trick or Tip? Your Vpn physician has the Cure!
I hope you have new knowledge about Troubleshooting. Where you'll be able to put to used in your evryday life. And above all, your reaction is passed about Troubleshooting.
0 comments:
Post a Comment